bladox.com Forum Index bladox.com
Turbo SIM Toolkit Adapter Forums
 
 FAQFAQ   SearchSearch   MemberlistMemberlist   UsergroupsUsergroups   RegisterRegister 
 ProfileProfile   Log in to check your private messagesLog in to check your private messages   Log inLog in 

AT&T Activated iPhone question

 
Post new topic   Reply to topic    bladox.com Forum Index -> General
View previous topic :: View next topic  
Author Message
usvi4me



Joined: 04 Jan 2008
Posts: 1

PostPosted: Fri Jan 04, 2008 8:15 pm    Post subject: AT&T Activated iPhone question Reply with quote

I have an AT&T activated 1.1.2 OTB iPhone jailbroken. (week 47)

I purchased on eBay a New Cingular Wireless AT&T 64K 3G Sim Card since I did not want to cut up the original AT&T activated iPhone sim I'm using when stateside.

I followed all directions to set up the iPhone with use off the Turbo Sim.

I have the following challenge:

When using the non-at&t sim with the turbo-sim,

1) the signal bar shows up with no signal showing
2) no carrier shows up
3) The turbo sim apps show up in the phone settings
4) The non-att&t sim's phone number shows up at the top of the contact list.
5) The non-at&t sim works fine in another phone.

Because of 3 and 4 I believe all the software is installed properly.

When I put the iPhone activated at&t sim back in, all works fine and the turbo-sim applications disappear from the settings.

Could the non-signal issue be that I used an incorrect non activated at&t sim ?

As always, any suggestions are greatly appreciated.
Back to top
View user's profile Send private message
Nekos



Joined: 16 Dec 2007
Posts: 31

PostPosted: Sat Jan 05, 2008 1:02 pm    Post subject: Reply with quote

Hi...

did you run Applesaft and SET the parameters ?
Back to top
View user's profile Send private message
A3Australia
Guest





PostPosted: Sat Jan 05, 2008 1:36 pm    Post subject: Re: AT&T Activated iPhone question Reply with quote

usvi4me wrote:
I have an AT&T activated 1.1.2 OTB iPhone jailbroken. (week 47)

I purchased on eBay a New Cingular Wireless AT&T 64K 3G Sim Card since I did not want to cut up the original AT&T activated iPhone sim I'm using when stateside.

I followed all directions to set up the iPhone with use off the Turbo Sim.

I have the following challenge:

When using the non-at&t sim with the turbo-sim,

1) the signal bar shows up with no signal showing
2) no carrier shows up
3) The turbo sim apps show up in the phone settings
4) The non-att&t sim's phone number shows up at the top of the contact list.
5) The non-at&t sim works fine in another phone.

Because of 3 and 4 I believe all the software is installed properly.

When I put the iPhone activated at&t sim back in, all works fine and the turbo-sim applications disappear from the settings.

Could the non-signal issue be that I used an incorrect non activated at&t sim ?

As always, any suggestions are greatly appreciated.


I reckon you activated with the AT&T SIM so there is a lockdown file on the iPhone with that AT&T SIMs info.

You would have to Virginize the iPhone - then go through all the usual steps to get to 1.1.2 and Jailbreak and Activate. Then you can use your TurboSIM with your SIM of choice.

A3 Australia
Back to top
Display posts from previous:   
Post new topic   Reply to topic    bladox.com Forum Index -> General All times are GMT
Page 1 of 1

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © 2001, 2005 phpBB Group